Mitsubishi Electric PK12 Manual de usuario

To our customers, Old Company Name in Catalogs and Other Documents On April 1st, 2010, NEC Electronics Corporation merged with Renesas Technology C

1Section 1 Components1.1 EV-Chip Board ComponentsTable 1.1 lists the product components of the EV-chip board (HS7055EBK81H: 3 x 100-pinconnector type)

21.2 Component NamesThe component names of the EV-chip board are described below.Top view1234CN3CN2CN1XXXX1111XXXX0000Side view876Station to EV-chip b

38. HS7055PWB30H: Includes connectors for interfacing with theuser system.

4Section 2 Preparation before Use2.1 Preparing the User SystemTable 2.1 lists the user interface pin assignment of the specific connector (FX2-100P-1.

5Table 2.1 Pin Assignment of the HS7055EBK81H User Interface (UCN1)Pin No. Pin Name Pin No. Pin Name Pin No. Pin Name1 GND 35 PJ6/TIO2G 69 PK15/TO8P2

6

7Table 2.1 Pin Assignment of the HS7055EBK81H User Interface (UCN2)Pin No. Pin Name Pin No. Pin Name Pin No. Pin Name1 AVCC 35 PA5/TIO3B 69 PC0/TxD12

8

9Table 2.1 Pin Assignment of the HS7055EBK81H User Interface (UCN3)Pin No. Pin Name Pin No. Pin Name Pin No. Pin Name1 NMI 35 MD1 69 GND2 GND 36 MD2 7

102.1.1 Recommended Mounting Pad Dimensions of the User SystemFigure 2.1 shows the dimensions of the recommended mounting pad (footprint) and position

Notice 1. All information included in this document is current as of the date this document is issued. Such information, however, is subject to chang

11UCN3101.067.31±0.1062.23±0.1071.95±0.1010.0P o sitio n in g holeUCN2Pin 1Pin 1UCN1φ2-1.9+0.1-0P=1.27±0.050.83.33.1Pin 1118.0pad for fixingU n it: m

122.1.2 Connector Position on the User SystemCAUTIONBefore connecting the connectors (FX2-100P-1.27SVL)to the user system, check the location of pin 1

1395.062.23±0.1071.95±0.103.33.1UCN31210099UCN11210099E x te rn al fra m e of the E V -chip boardUCN21210099140.0118.039.022.011.024.022.0Unit: m m

14HS7055PWB30HUser system socket FX2-100P-1.27SVL manufactured by HIROSE ELECTRIC CO.,LTDUser system boar8.7Unit: mmFigure 2.3 Component Height Rest

15Section 3 Connecting the EV-Chip Board to the UserSystem3.1 Connecting the EV-Chip Board to the User System3.1.1 Connecting the Specified ConnectorT

163.1.2 Connecting the Trace Cables to the EV-Chip BoardAlways switch OFF the emulator and user system beforeconnecting or disconnecting any CABLES or

17• Connecting the trace cables to the EV-chip boardAlign the trace cables with the station to EV-chip board interface connectors CN1, CN2, andCN3 on

18Tighten the screws to connect the trace cable connectors to the station to EV-chip boardinterface connectors while holding the HS7055PWB30H securely

193.1.3 Connecting the EV-Chip Board to the User System Board• Connecting the EV-chip board to the user system boardCheck the location of the FX2-100

20User system    CN3CN2  CN1H S7055PW B 20HH S7055PW B30HUCN1UCN2UCN3Figure 3.2 Connecting the EV-Chip Board to the User System

Regarding the change of names mentioned in the document, such as Hitachi Electric and Hitachi XX, to Renesas Technology Corp.The semiconductor operati

www.renesas-electoronics.comSH7055 Evaluation Chip Board (HS7055EBK81H) for the E8000 EmulatorUser’s ManualUser’s Manual

NoticeWhen using this document, keep the following in mind:1. This document may, wholly or partially, be subject to change without notice.2. All rig

PrefaceThis manual describes how to connect and operate the EV-chip board. The EV-chip boardincorporates an evaluation chip for connection to a user s

ContentsSection 1 Components.....................11.1 EV-Chip Board Components ...